machines de caoutchouc machines d'occasion à vendre (406)

Thyssen Krupp modèle GK270NC Banbury type mélangeur interne, 4 rotors tangentiels d’aile, Année de fabrication: 2003 Dernière chambre de design Continental! Trémie hydraulique et bloc d’alimentation. Corps et trémie seulement en bon état. La boîte de vitesses Unidrive et le moteur peuvent être cités si nécessaire (mêmes centres que 11D ou F270).

Farrel Pomini Modèle OOC Lab Banbury Mixer interne numéro de machine: 7511, Année: 1976 Volume net : 4,24 litres trémie pneumatique Moteur à vitesse variable DC 30kW. Complet avec panneau de contrôle, etc et en très bon état.

Francis Shaw 18/22 - Dump Extruder, Alimentation Crammer Longueur de vis 9ft 6. Reliance 400hp D.C., 1150 r.p.m., 480 volt. Grand Hopper/Chute au niveau du plancher suivant.

Nakata Zoki Kobe, Japon (Troester design) Duplex Extruder Unit Double 150mm dia PIN Type Extruders, Année de fabrication: 1990, avec Roller Feed, et duplex Die. Rapport L/D 16:1 Nombre d’épingles: 10 lignes x 8 pièces, broches de rechange inclus. Screw Speed 45 r.p.m. Moteurs 185kw D.C. vitesse variable, 415 volt, 3ph, 50hz. Livres et dessins complets disponibles. Thyristor Drives inclus. Panneau de démarrage et de contrôle pour l’extrudeur inférieur seulement. Die largeur utilisable 18, en bon état.

1 x Pont David 15/18 avec 40 'Face x 20 'die Roller Die. Pièces de rechange disponibles. Vis L/D 5:1, Crammer. Longueur du baril 7ft. Unité de virage à angle droit pour le flux du produit. Moteur à vitesse variable DC 200HP

Kobelco Twin Screw Roller Head Extruder (type horizontal), Modèle TSR-330 Assemblage de die de rouleau (TSR-33H005H) 38in large x 16po dia La matrice de rouleau s’éloigne de la section extrudant/mélangeur par bélier hydraulique. entraîné par 102kW DC moteur à vitesse variable à travers la boîte de vitesses de réduction Hansen (sur l’accouplement flexible afin que le rouleau matrice peut aller de l’avant / dos). Extrud de décharge à vis jumelle 330mm vis dia conduit par 90kW DC moteur à vitesse variable à travers la boîte de vitesses de réduction Hanson. En très bon état. Précédemment en cours d’exécution sous un F270 Banbury. Complet avec tous les contrôles, manuels et documentation, etc.

Farrel Pomini modèle F620 Banbury mélangeur interne, volume net de chambre de mélange : 710 litres Machine numéro 6515. Année originale de fabrication: 1972, mais le corps remplacé 1998 poids de lot approx à SG 1 - 533kg, 4 rotors d’aile, côtés forés, chambre soudée entièrement soudée, rotors et poids flottant, S.S.A. phoques à la poussière, porte de chute hydraulique avec actionneur linéaire, trémie pneumatique, boîte de vitesses unidrive avec 2 x CEM 1475kW, 1550A, 1000V, 800/1000rpm DC moteurs à vitesse variable, Commandes de conduite incluses, mais les contrôles de l’opérateur ne sont pas disponibles. En bon état (seulement utilisé pour le masterbatch composé de pneu). Pièces de rechange disponibles : haut de porte (nouveau), arbre de charnière (nouveau), joints de poussière de 2 x, joints larvaires et joints de roulement.

Troester 150mm dia PIN extruder Type: QSM150K, Série no 8622/80, Année de fabrication: 1980, mais rénové par Troester 2000 (nouvelle section vis et baril) Alimentation de rouleau de puissance, Rapport L/D 16:1 8 rangées de 8 broches, équipé d’un moteur à vitesse variable ASEA 212kW DC et de commandes (1800 tr/min). Complet avec des contrôles, etc et en très bon état.

Ligne de die De rouleau composée de:- 1 x Troester 200mm éttrud baril d’épingle Type QSM200K-16D alimentation en rouleau d’alimentation, 10 rangées de 8 broches, Rapport L/D 16:1 Série no 1816/88, année 1988, Avec l’unité de régulation de la température, Moteur à vitesse variable ASEA DC 282kW monté sur des rails (s’éloigne du calendrier pour nettoyer etc.) Tête de tôle hydraulique reliée directement à:- 1 x Adamson 24po dia x 68po large deux rouleaux calendrier, rouleaux percés périphériquement axe croisé, roulements de type buisson, réglage nip motorisé avec boîte de vitesses unidrive Moteur à vitesse variable ASEA DC 277kW Dispositif de serrage hydraulique pour extrudeur Ensemble de 4 x tambours de refroidissement Application de liquidation et de revêtement double Unité de craie Contrôle Siemens PLC. Ligne c ...

1 x Modèle Francis Shaw K6 Intermix, Année originale de fabrication: 1977, Corps reconstruit équipé de la série Carter no 242.93, Année: 1993, Décharge hydraulique de porte de goutte, Volume de chambre de mélange : Environ 112 litres Trémie pneumatique, 750HP, moteur d’anneau de glissement, 3ph, 50 Hz par Sturdigear 1460/15.7 boîte de vitesses de réduction de rame (cote 1000HP). Complet avec unité hydraulique et commandes de l’opérateur, etc. et en très bon état.

machine measurements: -- mmmachine weight: -- kgpower capacity: -- kWCondition: used, Specification: drum-type blast deburring machine type: MEWO Rotor TS 60- batch volume approx.: 1-100 litres,- working temperature: - 150°C- drum speed: 5 - 30 rpm- Blast wheel speed: 1,000 - 9,500 rpm- Control: Siemens S7 SimaticThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

roll diameter: 500 mmroll length: 1500 mmrolls drilled: Kernbohrung Nip adjustment: hydraulisch 0total power requirement: 110 kWCondition: used, overhauled Specification: Rolling mill 500 x 1500 mm - second-hand- roller diameter: 500 mm- roll length: 1500 mm- monoblock motor under the rollers- Fixed friction between the rollers- Rollers: with core bore, with central chamber for water cooling- Gap adjustments: NEW hydraulic- Hydraulic unit: NEW- Tilting material guide jaws made of steel with mechanical with mechanical safety interlock- Rollers: mounted on bronze bushes with circulating oil lubrication via pump- New Johnson-Fluiten ball swivel joints for connection to water circuit to water circuit- New safety brake for EMERGENCY STOP- New AC moto ...

roll diameter: 250 mmroll length: 500 mmrolls drilled: Kernbohrung nip adjustment: mechanisch drive power:: kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

machine measurements: 3.000 mmmachine weight: -- kgpower capacity: 90 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

roll diameter: 700 mmroll length: 2200 mmrolls drilled: Kernbohrung Nip adjustment: hyraulisch 0total power requirement: 160 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

Press force max.:: 3000 kNheating plates:: 600 x 630 mmelectrically heated:: °Cheating power:: kWpiston stroke:: 420 mmno. of stages:: 1 Condition: Used, reconditionedSpecification: Press 600 x 630 mm, second-hand- clamping force: 300 tonnes (3,000 kN)- closing: from bottom to top- Heating platens: 2 electric platens, with new heating rods- Heating platen dimensions approx.: 600 x 630 mm- Distance between the heating platens approx.: 420 mm- New electric valves- AC machine output oil pump: 5.5 kW- New control cabinet with Siemens 7’ touch panel- PLC control system make Siemens S7-1200- New cabling- Frequency inverter made by Schneider- Light barriers in the front area,Overhauled in accordance with CE standard safety regulationsOperating instructions and maintenance instructions in GermanWarranty: 1 yearThe data for this ad was created with ModulMWS - the sof ...

0: 200 °CTorque: - 0Dimensions (HxWxD): 680 x 1320 x 760 mmweight: 177 kgThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

machine measurements: 1500 x 2400 x 1150 mmmachine weight: -- kgpower capacity: 12 kWThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

screw ø:: 70 mmscrew length:: 22D screw speedl:: -- U/minCondition: usedSpecification: rubber extruder line – used COLMEC Extruder, Hot Air Channel, Cooling BathConsisting of:Extruder COLMEC 70 x 22D- Screw diameter: 70 mm- Screw length approx.: 22D- Extruder motor power: 37 kW- Cooling unit for extruderHot air oven:- Hot air oven power: 80 kW- Fan power: 2x 0.36 kW, 2x 1.5 kW- Stainless steel cooling bathThe system is in good condition and wasstill in operation until approx. 6 months ago- Sold as seen. The buyer is responsible for safety regulations. Without CE markingThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

roll diameter: 550 mmroll length: 1500 mmrolls drilled: peripher Nip adjustment: hydraulisch 0total power requirement: 110 kWCondition: used, overhauled Specification: rolling mill 550 x 1500 mm - used- roll diameter: 550 mm- roll length: 1500 mm- monoblock - motor under the rolls- Fixed friction between the rolls- Rolls: peripherally drilled, for water cooling- Gap adjustments: NEW hydraulic- Hydraulic unit: NEW- tiltable steel material guide jaws- Rollers: mounted on bronze bushes with oil circulation lubrication via pump- new ball bearing slewing rings for connection to water circuit- Safety brake for EMERGENCY STOP- New AC motor 110 kW - 400 V - 50 Hz - New pan for receiving the mixture- Safety bars bi-directional- New electrical control cabinet with PLC system S7-120 ...

screw ø:: 60 mmscrew length:: 11D screw speedl:: -- U/mindrive power:: 18,5 kWCondition: used, reconditionedSpecification: rubber extruder – used- Screw diameter: 60 mm- Screw length approx.: 11D- New screw- Cylinder refurbishment- Feed roller refurbishment- New safety cage- New rotary joint for water- New AC motor: 18.5 kW- New control cabinet with Siemens S7-1200 PLC system- New control panel with Siemens KTP700 Basic touch panel- New Siemens G120 frequency converter for variable speed- Remote maintenance device- New cabling- Pressure sensors on the extruder head- Safety device- CE marking and an operating and maintenance manual in EnglishRefurbished in accordance with CE standard safety regulationsWarranty: 1 yearOption: TCU for temperature control of the water up to 95°C, for placement near the extruderThe data for thi ...

clamping force: 2.700 kNinjection volume: 6.000 cm³screw diameter: -- mmplaten size: 560 x 630 mmCondition: second-hand,Specification: rubber injection moulding machine - second-hand, partially dismantled, but would be restored to its previous condition EUROMAP size 2500 – 7000Clamping unit:- Clamping unit: vertical- Clamping force: 2.700 kN- Platen size: 560 x 630 mm- Max. stroke: 550 mm (see data sheet) Injection unit:- Max. injection volume: 6,000 cm³- Injection pressure: 2150 bar- Power supply: 3x 400 V, 50 Hz, N, PE- Motor power: 28,2 kW- Installed heating capacity: 49,9 kW- Weight: Clamping unit approx.: 6,040 kg Injection unit approx.: 2,700 kg Hydraulic un ...

clamping force: 4.500 kNinjection volume: 3.300 cm³screw diameter: -- mmplaten size: 670 x 780 mmCondition: second-hand,Specification: rubber injection moulding machine - second-hand EUROMAP size 4000 – 7000Clamping unit:- Clamping unit: vertical- Clamping force: 4500 kN- Platen size: 670 x 780 mm- Max. stroke: 600 mm (see data sheet) Injection unit:- Max. injection volume: 3,300 cm³- Injection pressure: 2150 bar- Power supply: 3x 400 V, 50 Hz, N- Motor power: 35,5 kW- Installed heating capacity: 73,9 kW- Weight: Clamping unit approx.: 8,400 kg Injection unit approx.: 2,700 kg Hydraulic unit with oil and control cabinet 2,200 kg Additional equipment (approx.): 3,000 kg  ...

clamping force: 4.500 kNinjection volume: 5.600 cm³screw diameter: 610 - 985 mmplaten size: 670 x 780 mmCondition: second-hand,Specification: rubber injection moulding machine - second-hand EUROMAP size 4500 – 12300Clamping unit:- Clamping unit: vertical- Clamping force: 4500 kN- Platen size: 670 x 780 mm- Max. stroke: 610 - 985 mm (see data sheet) Injection unit:- Injection unit type: ADV- Max. injection volume: 5,600 cm³- Injection pressure: 2200 bar- Power supply: 3x 400 V, 50 Hz, N, PE- Pump capacity: 27 kW- Weight: Cutting unit approx.: 10,200 kg Injection unit approx.: 3,500 kg Hydraulic unit with oil: 2,600 kg Accessories approx.: 4,700 kg Total weight approx.:  ...

clamping force: 4.500 kNinjection volume: 5.000 cm³screw diameter: -- mmplaten size: 670 x 780 mmCondition: second-hand,Specification: rubber injection moulding machine - second-hand EUROMAP size 4500 – 10000Clamping unit:- Clamping unit: vertical- Clamping force: 4500 kN- Platen size: 670 x 780 mm- Max. stroke: 600 mm (see data sheet) Injection unit:- Max. injection volume: 5,000 cm³- Injection pressure: 2060 bar- Power supply: 3x 400 V, 50 Hz, N, PE- Motor power: 38 kW- Installed heating capacity: 67.5 kW- Weight:Clamping unit approx.: 8,900 kgInjection unit approx.: 3,200 kgHydraulic unit with oiland control cabinet 2,350 kg- For dimensions, see the installation data in the appe ...

clamping force: 300 kNinjection volume: 180 cm³screw diameter: -- mmplaten size: 300 x 300 mmCondition: second-hand,Specification: C-frame injection moulding machine for rubber - second-handClamping unit:- Clamping unit: vertical- Clamping force: 300 kN- Platen size: 300 x 300 mm Injection unit:- Maximum injection volume: 180 cm³- Mains supply: 3x 400 V, 50 Hz- Power rating: 11 kW- Control system: MAPLANThe machine is still in production and can be viewedin operation.The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

roll surface width: 450 mmroll diam. toproll: 203 mmroll diam. bottom roll: 203 mmoutput: 8,8 kwSmall roll gap 0.1 mmMaximum roll gap 47 mmFront/rear roll speed 5-30 rpmFront/rear roll speed 3.2-19.1 m/minRolls individually drivenFriction variable max. 1:6Manual gap adjustmentManual speed controlExternal temperature controlRollers internally cooled (water cooling)Emergency stop handle (manual operation) on both sidesThe tech. Data are manufacturer or operator information and therefore non-binding. We reserve the right to prior sale, Our terms and conditions of sale apply exclusively.About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours ...

speed of feed:: 60 m/minfeed:: 5 - 99.999,9 mmcuts max.:: -- Schnitte/mcross-section width:: 5 - 90 mmcross-section heigth:: 5 - 90 mmCondition: Second-hand,Specification: Strip and tube cutting unit • Cutting unit: Impact blade cutting with cutting sleeves• Material diameter approx.: 5–90 mm• Conveyed by two drive belts• Distance between the belts max.: 90 mm • Belt adjustment via motor, controlled via control panel• Lower belt fixed, upper belt motor-adjustable• Belt contact length approx.: 500 mm• Contact width: 80 mm• With a maximum speed of approx.: 60 m/min• Electronic length measurement: 5 – 99,999.9 mm • Maximum cutting accuracy: +/- 2 mm• Cutting is performed by a servo motor: 1 kW• Power supply: 380/400V, 50Hz, 5kW• Material feed directio ...

volt: 380 Vweight: 1,4 t: The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

clamping force: 350 kNinjection volume: 170 cm³screw diameter: 36 mmplaten size: 380 x 300 mmCondition: second-hand,Specification: C-frame injection moulding machine - second-handClamping unit:- Clamping force: 350 kN- Platen size: 380 x 300 mm- Heating power of the plates: 6 kW- Clamping/opening stroke: 200 mm- Clearance between the plates: 250 mm- Clamping direction: from belowInjection unit:- Pressure: 1,050 kg/cm²- Maximum injection volume: 134 cm³- Screw diameter: 35 mm- Max. screw speed: 30–110 rpm- Metering stroke: 165 mm- Injection: from above- Voltage: 3 × 400 V, 50 Hz, N, PE- Pump drive power: 11 kW- Hydraulic motor power: 10 kW- Dimensions LxWxH: 2,400 x 1,200 x 3,300 mm- Weight ap ...