Voir les détails
SEMA END 70-1-2-S-100-NC-A Facing and Centering Machine
d’occasionVendeur vérifié
Demander le prix
Directement au vendeur
1 / 5
Caractéristiques techniques
· ID 170397445Machines d’occasion
- État
- d’occasion
- Année de construction
- 2008
- Emplacement
- Staufenberg 1
Identifikation
FabricantSEMA
ModèleEND 70-1-2-S-100-NC-A
Numéro d’article1113-235071
Technik
Quantité1
Description
max. workpiece diameter:29 mm
min. workpiece diameter:26 mm
workpiece length:66 mm
the system was originally delivered for the following workpiece sizes: diameter 26mm - 29mm length 65mm - 66mm
Changing parts in the clamping device, handling, etc. would probably result in diameters of up to approx. Ø50mm
Total length will probably be almost 400 mm possible with a few conversions.
Also dependent on tool lengths, machining lengths on the component, etc.
Workpiece: Piston pin
Drawing number: WHT 000 718, WHT 000 718 A
Workpiece dimensions (Ø, WxH): Ø26 x 66; Ø29 x 65
Length: 66 or 65 mm
Material: 17Cr3
Quantity: xxx parts / year
Cycle time: 5 sec.
However, workpiece lengths up to 600mm are manageable. The machining diameter can be adjusted if the appropriate tools are available. The clamping station can currently only accommodate this product. However, this can be adapted by changing the clamping prisms. The parts that were typically produced on this machine left the system via a chute onto a conveyor belt. If longer parts were to be manufactured, this would need to be examined in detail.
Texte, Bilder, Grafiken, Layout, Strukturen und Algorithmen etc. unterliegen weltweitem Urheberrecht.
Unerlaubte Verwendung der Daten, werden sowohl strafrechtlich als auch zivilrechtlich verfolgt.
Das ausschließliche Urheber- / Nutzungsrecht dieser Daten wurde nachfolgender Person eingeräumt.
Copyright © 2005-2025, Josef Weber. All rights reserved.
min. workpiece diameter:26 mm
workpiece length:66 mm
the system was originally delivered for the following workpiece sizes: diameter 26mm - 29mm length 65mm - 66mm
Changing parts in the clamping device, handling, etc. would probably result in diameters of up to approx. Ø50mm
Total length will probably be almost 400 mm possible with a few conversions.
Also dependent on tool lengths, machining lengths on the component, etc.
Workpiece: Piston pin
Drawing number: WHT 000 718, WHT 000 718 A
Workpiece dimensions (Ø, WxH): Ø26 x 66; Ø29 x 65
Length: 66 or 65 mm
Material: 17Cr3
Quantity: xxx parts / year
Cycle time: 5 sec.
However, workpiece lengths up to 600mm are manageable. The machining diameter can be adjusted if the appropriate tools are available. The clamping station can currently only accommodate this product. However, this can be adapted by changing the clamping prisms. The parts that were typically produced on this machine left the system via a chute onto a conveyor belt. If longer parts were to be manufactured, this would need to be examined in detail.
Texte, Bilder, Grafiken, Layout, Strukturen und Algorithmen etc. unterliegen weltweitem Urheberrecht.
Unerlaubte Verwendung der Daten, werden sowohl strafrechtlich als auch zivilrechtlich verfolgt.
Das ausschließliche Urheber- / Nutzungsrecht dieser Daten wurde nachfolgender Person eingeräumt.
Copyright © 2005-2025, Josef Weber. All rights reserved.
Demander des informations sur cette machine
Votre demande est transmise directement au vendeur de cette machine.
