travail de la tôle machines d'occasion à vendre (3,276)

sheet width: 3060 mmplate thickness: 6.0 mmthickness at Niro-steel: 4.0 mmdistance between columns: 3100 mmdown holder: 16 Stückno. of strokes: 20 Hub/minoil volume: 160 ltr.cutting angle: 1.6 °Control: ELGO Number of working hours: ~ 1.100 htotal power requirement: 11.0 kWweight: 5250 kgrange L-W-H: 3800 x 1940 x 1560 mm from a maintenance workshop with only approx. 1.100 operating hours ()Equipment:- electro-hydraulic swing beam shears- ELGO NC control unit for electric back stop Input of target/actual position value possible- NC electro-motoric back stop travel path of back stop X = 750 mm back stop ball screw with no play travel speed 100 mm/sec- electric cutting length limitation cutting length limitation to increase the number of strokes/min.- manual cutting gap adjustment, via eccentric- tip operation with push buttons on the control panel on the left- front support plates with  ...

sheet width: 2540 mmplate thickness: 2.00 mmthickness at Niro-steel: 1.25 mmno. of strokes: max. 63 Hub/mincutting angle: 1.13 Gradtable height: 750 mmtable width: 320 mmdistance between columns: 2620 mmback stop - adjustable: 5.0 - 550 mmControl: konv. engine output: 3.0 kWweight of the machine ca.: 1600 kgrange L-W-H: 3100 x 1980 x 1400 mmEquipment:- robust / motorized swing cut guillotine shears- break-proof, torsion-free steel welded construction- compact and clear machine design- manual back stop, with analogue display adjustable from the front stepless adjustment over the entire travel range- recessed grips in the support table- 1x hold-down bar- 1x side stop- 3x support arms- 1x freely movable foot switch- operating instructions (PDF) Special accessories included:- sheet metal holding device for thin sheet metal cutsThe data for this ad was created with ModulMWS - the software sol ...

sheet width - max.: 2535 mmplate thickness: 4.0 mm STplate thickness: 2.5 mm VAplate thickness: 6.0 mm ALUnumber of strokes - loaded: 20 Hub/mincutting angle: 1.7 °work height max.: 900 mmtotal power requirement: 8.5 kWweight of the machine ca.: 3400 kgrange L-W-H: 2916 x 2250 x 1760 mm Machine from training workshop good / well-maintained condition ()Equipment:- robust electro-hydraulic swing cut guillotine shears- electro-motorized rear stop- electric cutting length limiter- electro-motorized cutting gap adjustment- front support table including recessed grips- 1x stable side stop, with scale and tilting cam- 3x stable, front support arms- 1x freely movable foot switch- front finger guard- EMERGENCY STOP button at the front- operating instructions Special accessories included:- pneumatic sheet holding device for thin sheet metal cutsThe data for this ad was created with ModulMWS - the ...

sheet width: 1040 mmplate thickness: 2.50 mmthickness at Niro-steel: 1.25 mmno. of strokes: max. 90 Hub/mincutting angle: 2.70 Graddistance between columns: 1060 mmwork height max.: 940 mmback stop - adjustable: max. 550 mmcolumn arm: 120 mmvoltage: 400 Vengine output: 4.0 kWweight of the machine ca.: 820 kg.range L-W-H: 1650 x 1200 x 1250 mmEquipment:- robust / motorized crank guillotine shears with motor drive- break-proof, torsion-free steel welded construction- compact and clear machine design- manual back stop, with analog position display adjustable from behind continuous adjustment over the entire travel range travel range max. 550 mm- 1x hold-down bar- 1x side stop- 1x front support arm- original operating instructionsThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 1270 mmplate thickness: 1.75 mm STplate thickness: 2.00 mm ALUplate thickness: 2.50 mm KUthickness at Niro-steel: 0.80 mmdistance between columns: 1300 mmdaylight opening: OW ~ 380 mmwork height max.: 900 mmadjustment: UW 60.0 mmbending angle max.: 180 °weight: ca. 200 kg kgrange L-W-H: 2000 x 520 x 1500 mm good condition () Bending splint e.g. regroundFurnishing:- robust, manual folding machine- manual lifting by hand lever (incl. gas pressure damper)- manual clamping of the upper beam by means of a handwheel on the side- manual lower beam adjustment- Bending angle fixed stop, with analogue angle display- Upper beam with large opening width- Instructions / description Machine link :http://mhp.logotech.de/hpm/v7/Datenblatt/datenblatt.php?machineno=100 8-9355182The data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

sheet width: 6020 mmplate thickness: 6.0 mmthickness at Niro-steel: 4.0 mmback stop - adjustable: max. 1000 mmwork height max.: 1030 mmno. of strokes: 5 - 10 Hub/mincutting angle: 0.5 - 3.0 °down holder: 33 StückControl: SC 100 T engine output: 11.0 kWweight of the machine ca.: ca. 27000 kgrange L-W-H: 7650 x 2400 x 2885 mm New price in 2021 ~ 160.000 Euro Special price upon requestEquipment:- Robust electro-hydraulic guillotine shear Design: Guide rail- HACO CNC control model SC 100 T, pivoting at the front left Control unit with LCD display Pre-selected positioning of the backgauge Digital display of actual position Electro-hydraulic cutting angle adjustment Electro-hydraulic cutting gap adjustment Programmable retraction from the backgauge Programmable cutting length limitation Automatic + manual programming mode Emergency stop switch- CNC electro-motor-driven material/backgauge On ...

sheet width: 3050 mmplate thickness: 6.35 mmthickness at Niro-steel: 4.00 mm: 8.00 mmdown holder: 10 Stückcutting angle: 0°40 - 2°20 Grad: 3340 mmwork height max.: 860 mm: 575 mmControl: GP 37W2 : 13 - 33 0: max. 315 baroil volume: 100 ltr.total power requirement: 6.0 kWweight of the machine ca.: 6030 + 1850 kg In good condition () current new price including accessories approx. 110.000 Euro Special price upon request- in checked conditions - machinevideo -https://www.youtube.com/watch?v=3JUqSaaJkFQEquipment:- Robust CNC electro-hydraulic guillotine shear- AMADA CNC touch control, front left (GP 37W2) Machine control including information display Main display with 4 control panels Control/operation of all functions Max. 50 cutting programs with 15 sequences each- CNC electro-motorized backgauge Travel speed 100 mm/sec.- CNC electro-hydraulic cutting angle adjustment- CNC electro-hydra ...

sheet width: 2050 mmplate thickness: 4,5 mm max.plate thickness: 4,0 mm anbiegenroll length: 2050 mmmin. dia.: 210 mmroll diam. toproll: 140 mmweight: 1530 kgrange L-W-H: 3220 x 1200 x 900 mmFurnishing:- Robust electro-mechanical bending machine- 2x central rollers driven by an electric motor (top and bottom roller)- Top roller can be swiveled out manually, with folding bearing- including conical bending device- freely movable control panel- Lower roller manually adjustable, by hand wheel- asymmetrical roller arrangement- self-braking main motor- Safety device (safety line with switch unit)- CE mark/Declaration of ConformitySpecial equipment included in the price:- hardened rollers- Motorized side roller adjustment- Digital position display for motor-driven adjustable side rollerThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

I - beam section - flat steel: 80 x 20 (d 1200) mmI-beam section - upend: 80 x 25 (d 2100) mmL-beam: 50 x 50 x 6 (d 1000) mmbar material - diameter: 40.0 (d 800) mmsquare material: 60x60x3 ( d 4000 ) mmrectangle: 80x30x3 ( d 6000 ) mmroll surface width: 177x60 (18x5 Nut) mmbar material dia. max.: 70 x 2.0 (d 1600) mmtool adaptor: 60.0 mmturning speeds: 6.4 m/min.oil volume: 80.0 Litertotal power requirement: 4.75 kWweight: 1080 kgrange L-W-H: 940 x 1260 x 1390 mm Exhibition machine from 2022 with only approx. 2x operating hours Condition as NEW Special price on requestEquipment:- electro-hydraulic ring/profile bending machine- hydraulic bottom/side roller adjustment for extra small bending radii- bottom/side roller can be adjusted individually- 3x driven rollers- divided roller segments- digital position display of the bottom/side rollers Display with touchscreen function- hardened tool ...

sheet width: 3100 mmplate thickness: 13,0 mmthickness at Niro-steel: 8,0 mmdown holder: 14 Stückno. of strokes: 11 Hub/minoil volume: 310 ltr.cutting angle: 2,0 °throat: 350 mmtable height: 900 mmtotal power requirement: 22,0 kWweight of the machine ca.: 12200 kgrange L-W-H: ca. 4100 x 2300 x 2235 mm--------------------------------------------------heavy electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment-------------------------------------------------- Furnishing:- CNC electr. / hydraulic swing cut shears- CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Number of pieces Cutting length limitation Material preselection, including sheet thickness Cutting line lighting- motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. Can be folded up at max.tr ...

sheet width: 3100 mmplate thickness: 10,0 mmthickness at Niro-steel: 6,0 mmdown holder: 14 Stückno. of strokes: 13 Hub/minoil volume: 260 ltr.cutting angle: 2,0 °throat: 350 mmengine output: 22,0 kWback stop - adjustable: 1.000 mmweight: 10.575 kg.range L-W-H: 4,05 x 2,5 x 2,17 m--------------------------------------------------heavy electr. / hydraulic CNC swing cut shears with CYBELEC CNC touch screen control with electr. / hydr. Kerf adjustment--------------------------------------------------Furnishing :- CNC electr. / hydraulic swing cut shears- CYBELEC CNC touch screen controller, model CybTouch 8 Backgauge preselection - X axis Cutting gap adjustment Quantity Cutting length limitation Material preselection, including sheet thickness Cutting line lighting- motorized backgauge, travel = 1,000 mm (X axis) on ball screws autom. Can be folded up at max.travel, for longer cuts- 1x sid ...

sheet width: 3100 mmplate thickness: 8,0 mm STpre-bending: 6,0 mm STdiameter of upper rolls: 230 mmside roll diameter: 210 mmdiameter of lower rolls: 190 mmtotal power requirement: 7,5 kWweight of the machine ca.: 6.020 kg.dimensions of the machine ca.: 5142 x 1390 x 1300 mmFurnishing:- electro-hydraulic 4-roller bending machine- 2x driven main rollers (upper & lower roller)- with hydraulic conical bending device- Induction hardened rollers- including straightening function for welded pipes- Control unit / display with touch screen function digital position display for the two side rollers- mobile control panel- 2x bending speeds selectable- hydraulic folding bearing- Safety device (safety line with switch unit)- Pressure gauge / pressure indicator for the rollers- CE mark + declaration of conformity- Operation manualThe data for this ad was created with ModulMWS - the software solution  ...

plate thickness: max. 5.0 mmtube diameter: 27.9 - 61.0 mmmotor: 400 Volttotal power requirement: 2.2 kWweight of the machine ca.: 93.0 kg.The AL1-2U electric pipe notcher is started at the push of a button, and the pipe notcher is driven continuously. This means you can continually work on new parts without having to switch the machine on again each time.With the electrically driven AL1-2U pipe notcher you can notch pipe outer diameters of Ø 26.9 (3/4?), Ø 33.7 (1?), Ø 42.4 (1 ¼), Ø 48.3 (1 ½), Ø 60.3 (2?).This pipe notcher is also suitable for notching a zinc outlet in round and rectangular metal pipes. You can notch pipe outer diameters of ø 20.0 -60.3.Do you often notch pipes? Then the electrically driven pipe notcherAL1-2U with the 2.2 kW electric motor is just the thing for you. The motor forms a unit with the special eccentric shaft that drives the notching tool. The motor  ...

plate thickness: max. 5.0 mmtube diameter: 27.9 - 61.0 mmmotor: 400 Volttotal power requirement: 2.2 kWweight of the machine ca.: 87.0 kg.The AL1-2E electric pipe notcher is started at the push of a button, and the pipe notcher is driven continuously. This means you can continue to work on new parts without having to switch the machine on again each time.With the electrically driven AL1-2E pipe notcher you can notch pipe outer diameters of Ø 26.9 (3/4?), Ø 33.7 (1?), Ø 42.4 (1 ¼), Ø 48.3 (1 ½), Ø 60.3 (2?).Do you often notch pipes? Then the electrically driven AL1-2E pipe notcher with the 2.2 kW electric motor is just right for you. The motor forms a unit with the special eccentric shaft that drives the notching tool. The motor is also equipped with an on/off switch with 0-voltage protection and a protective cap.Equipment:- electric motor pipe notching machine- for pipes 27.9 - 34 ...

sheet width: 1050 mmplate thickness: 2.0 mmroll length: 1070 mmroll diam. toproll: 75.0 mmengine output: 1.5 kWweight: 325 kgrange L-W-H: 1530 x 700 x 1160 mm Exhibition machine - like NEW not yet in use () Special price on requestEquipment:- electro-motor-driven 3-roller round bending machine- asymmetrical roller arrangement- 2x driven rollers using a brake motor- manual folding bearing for quick removal of the workpiece- wire insertion grooves on the bottom and rear rollers- double foot switch for R/L running including emergency stop button- rear roller feed with ratchet lever- electrical safety deviceThe data for this ad was created with ModulMWS - the software solution of LogoTech oHG.

pressure: 100 tchamfer lenght: 2600 mmdistance between columns: 2200 mmcolumn arm: 410 mmram stroke speed: 200 mm/secwork speed: 9.5 mm/secreturn speed: 155 mm/secwork stroke: 275 mmdayligth: 530 mmtable height: 900 mmtable width: 90.0 mmoil volume: 150 ltr.voltage: 400 Volttotal power requirement: 7.5 kWweight: 6850 kgrange L-W-H: 3750 x 1950 x 2800 mm-------------------------------------------------- Press brake with special equipment increased installation height increased cylinder stroke as well as increased bending beam speeds-------------------------------------------------- Furnishing:- DELEM CNC control model DA 53T (touchscreen)- Motorized backgauge with R-axis, on recirculating ball spindles- X = 800 mm R = 250 mm with 2 stop fingers- controlled axes Y1 - Y2 - X - R - C (crowning)- electr. Crowning controlled by CNC- Upper deer foot tool with PS 135.85-R08, system A with quick- ...

pressure: 220 tchamfer lenght: 3100 mmdistance between columns: 2600 mmcolumn arm: 410 mmram stroke speed: 180 mm/secwork speed: 10.0 mm/secreturn speed: 185 mm/secwork stroke: 275 mmdayligth: 550 mmtable height: 930 mmtable width: 200 mmoil volume: 300 ltr.voltage: 400 Volttotal power requirement: 18.5 kWweight: 11286 kgDimensions (HxWxD): 4550 x 2250 x 2850 mm-------------------------------------------------- HIGH-SPEED hydraulic press brake withincreased installation heightincreased cylinder strokeenlarged projection-------------------------------------------------- Furnishing:- DELEM CNC control model DA 66T- swiveling touchscreen control unit- 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning- electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm- on ball screws- controlled electr. Stop fingers Z1 + Z2- split upper deer foot tool Roleri 135.85.R08, Sys ...

pressure: 175 tchamfer lenght: 4100 mmdistance between columns: 3600 mmcolumn arm: 410 mmram stroke speed: 180 mm/secwork speed: 12.0 mm/secreturn speed: 190 mm/secwork stroke: 275 mmdayligth: 550 mmoil volume: 300 ltr.table height: 900 mmtable width: 90.0 mmvoltage: 400 Volttotal power requirement: 15.0 kWweight: 12100 kgrange L-W-H: 5.100x2.150x2.850 mm-------------------------------------------------- HIGH-SPEED hydraulic press brake withincreased installation heightincreased cylinder strokeenlarged projection-------------------------------------------------- Furnishing:- DELEM CNC control model DA 66T- swiveling touchscreen control unit- 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning- electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm- on ball screws- controlled electr. Stop fingers Z1 + Z2- split upper deer foot tool Roleri 135.85.R08, System A-  ...

sheet width: 1050 mmplate thickness: 2,0 mmdistance between columns: 1050 mmdown holder: 1 Stückfence: Tisch 80 - 480 mmfence: Breiten 0 - 600 mmtable-size: 1300 x 600 mmwork height max.: 760 mmtotal power requirement: manuell kWweight of the machine ca.: 413 kg.range L-W-H: 2,0 x 1,04 x 1,6 m- Including adjustable stop on the work table for miter cuts- The knife can be lifted easily thanks to the counterweight on the back- Large work table for safe placement of the sheet metal plates- Sheets can be pushed through, i.e. longer sheets can be cut- Handwheel on the front to adjust the back gauge- Comes with a robust cast iron base as standard- Long service life thanks to knives made of quality steel- Standard with hold-down device including quick-release clamp- Robust machine construction for high stabilityFurnishing:- manual lever shears- stable execution- hold-down bars- Side scale with  ...

I - beam section - flat steel: 80 x 16 (d 1200) mmI-beam section - upend: 50 x 15 (d 1000) mmL-beam: 50 x 5 (d 1200) mmround material: 40.0 (d 800) mmbar material dia. max.: 70 x 2.0 (d 1600 ) mmsquare material: 80x30x3 (d 4000) mmchannels - flange: UNP 80 (d 800 ) mmbending speed: 4.4 m/minroll diam. toproll: 157 mmbore: 50.0 mmoil volume: 18.0 Litertotal power requirement: 1.1 kWweight: 485 kg Exhibition machine from 2025 with only approx. 2x operating hours Condition as NEW Special price on requestEquipment:- electro-hydraulic ring/profile bending machine- hydraulic bottom/side roller adjustment for extra small bending radii- bottom/side roller can be adjusted individually- 3x driven rollers- divided roller segments- digital position display of the bottom/side rollers Display with touchscreen function- hardened tool holder (42CrMo4)- machine base- 2x manually adjustable side guides- h ...

Force de poinçonnage : 500 kN, profondeur de gorge : 610 mm, course : 60 mm, diamètre max. du trou dans l’acier épaisseurs 15 mm/9 mm/4,5 mm : 30 mm/50 mm/100 mm, épaisseur max. du matériau : 15 mm. Dimensions de la machine X/Y/Z : env. 1100mm/1550mm/1750mm, poids : env. 1650kg. Une inspection sur place est possible.

Force de coupe max. : 220 kN, puissance laser : 3200 W, connexion à l’azote : 30 bar, connexion à l’oxygène : 20 bar, charge connectée : 76 kVA, heures de fonctionnement au début de l’année 2025 : 67 766 h, avec laser Trumpf TLF 3200 et refroidisseur RIEDEL L 15/21 TR3/19.00, réfrigérant : R134a, poids de remplissage : 11,5 kg, haute pression : 20,2 bar. Outils supplémentaires disponibles. Une inspection sur place est possible.

Key data: 650 mm

Cisailles à levier à pied pour tôles

Cisailles électriques pour tôles

Key data: 4000 mm

Ref.Nr. 00883 Nom du système : Cisailles guillotines d’occasion Fabricant I.MA. L Modèle : CESO1A, Speed 64 Année de construction 2003 Portée de travail 4m Dimensions 3700 x 1950 x 2100 mm Poids 8500 kg Test de sécurité de la presse selon le rapport de test BGR 500 lt. Prochain examen en janvier 2026

Press brake tool, bending tool, die, upper knife, upper tool, straight tool -Bending tool: length 515 mm -Tool angle: 90° -Dimensions: see drawing in the photos -Dimensions: 515/14/H75 mm -Weight: 3.8 kg

Key data: 100 t, 215 mm, 3100 mm

Ref.Nr. 00882 Nom du système : Presse plieuse d’occasion Fabricant : Beyeler Modèle PR4 1000 KN x 3100 mm Année de construction 2000 Heures de la machine Non visible Puissance 100 tonnes Plage de travail 3100mm Système de contrôle DNC 80 Tension secteur 400V Puissance connectée 5,5 kW Poids de la machine 7000 kg Fréquence secteur/Frequez 3 ~ 50Hz Pré-fusible Max 20 AT Air comprimé max 8Bar Vitesse de fermeture maximale mm/s 200mm/s Vitesse de pressage 1-10 Course maximale 215mm Temps d’arrêt maximum 110mS Distance de sécurité minimale 350mm État technique Entièrement fonctionnel

Key data: 4020 mm, 1 mm

avec réglage de l’épaisseur du matériau, hydraulique sur le côté gauche de la machine, sans cisaille à rouleaux, poutre de pliage avec rail de fixation amovible env. 8 mm, 3 doigts d’arrêt, commande sur le bras pivotant, La machine est réparée, vérifiée, nettoyée par un professionnel et est alors entièrement fonctionnelle. Une série d’essai est effectuée. Longueur de travail : 4020 mm Épaisseur max. de la tôle d’acier : 1,5 mm Épaisseur max. de la tôle aluminium : 2,5 mm Epaisseur de la tôle max. VA : 0,8 mm Butée arrière (max.) : 1000 mm Projection : 1000 mm Couleur : bleu Puissance totale requise : 16 A Espace requis approximatif : 6000 x 2000 x 1900 mm Poids env. : 5000 kg Course du faisceau supérieur (largeur d’ouverture) : 200 mm sans ciseaux à rouleaux Nombre de supports : 5 pièces Angle de flexion (max.) : 145 degrés N ...

poids de la machine env. : 16 tlargeur de la feuille : 3150 mmépaisseur de la feuille - max. : 16 mm largeur de la feuille - min. : 1,6 mmtension : 400 Vrange - haute résistance : 3950x2475x2520 mmLes données de cette annonce ont été créées avec ModulMWS - la solution logicielle de LogoTech oHG.

Offre 25290 Spécifications: - Largeur de travail max. 3040 mm - Épaisseur max. du matériau à 40 kg / mm², résistance 2 mm - Réglage de l’angle de flexion sélectionnable 6 - 135 - Plus grande largeur d’ouverture / course de la poutre supérieure 250 mm - Réglage de la hauteur - poutre de flexion 50 mm - la poutre inférieure 50 mm - Entraînement de la traverse montante 400 V / 0,37 kW - Entraînement du faisceau de flexion 400 V / 0,75 kW - Butée arrière manuelle - Attelle de flexion de patte de chèvre fendue - Encombrement approximatif L 4000 x H 1400 x P 1200 mm - Poids env. 3500 kg