autres machines à bois machines d'occasion à vendre (1,349)

Robland X31 combi 5 fois, bon état, 2,2 kW, longueur de table de 1500 mm, largeur de table de 310 mm, 3 couteauxPrix susceptibles de changer, erreurs, erreurs d’impression et de composition à caractères exceptées

Break 5 vitesses Robland X310, bon état, 2,2 kW, 3 pales, environ 500 kgPrix sujets à changements, erreurs, erreurs d’impression et de composition à caractères exceptées

Hardened precision steel bar guided sliding aluminium table Parallel fence with micrometric fine adjustment. Sawblade and milling spindle immersible below the table. Telescopic fence 1800 mm with two flip stops. Stable outrigger table for working heavy plates. With own motor for the scoring unit for an easy deactivationTechnical Data:Circular saw:max. sawblade diameter 315 mmspindle diameter 30 mmmax. cutting width at parallel f. 1100 mmmax. cutting height, 90°/45° 103 mm/72 mmengine power 5 kW S6 (4kW S1)suction diameter 120 mmSpindle shaper:spindle diameter 30 mmspindle tilt 90°/45°spindle travel 175 mmspindle speed 10000/8000/6000/5000/4000/3000engine power 5 kW S6 (4kW S1)weight 790 kgincl accessories: Sliding table length 2300 mm, scoring unit4 kW motor, integral fence 500 mm, upper suction, degree raster at outrigger table.

Machine à déchiqueter le bois Machine silencieuse à basse vitesse avec tiroir de presse WL12/30 Dimensions de la trémie 1200x1200 Diamètre de l’arbre 368mm 58 lames de coupe sur deux rangées Crépine 15/20mm Moteur principal 30kW Poids env. 3200kg

Usine de tri de longueur Usine de tri de bois scié MAYRHOFER 5-Boîtes Longueur totale : env. 22 mètres Courant: 1. Boîte : 1 mètre 2ème boîte : 1,5 mètre 3. Boîte : 2 mètres 4. Boîte : 2,5 mètres 5. Boîte : 3 mètres bon état - entièrement fonctionnel - peut encore être visualisé pendant le fonctionnement Lieu : Autriche, près de Graz

Diamètre max 485mm Longueur min 1500mm, Longueur max 5500mm Puissance d’entraînement du disque rotor 315kw Séparateur d’étapes d’alimentation, courroie d’alimentation, détecteur de métaux Retrait Bruks 2x vis 1x 600x6.500mm et 1x 800x9.500mm Longueur des copeaux de bois 25mm Armoires Année de construction/mise en service 2004 Heures de travail env. 12500 heures Capacité 80-100 Qm3/h

Sciages hydrauliques en bois, fonctionnels Détails sur demande

Accès au bois rond avec 4-3

Pleine porte Esterer SS45 a été nommé generalueberholt Passage 450 mm 340 upm 500 Hub avec une insensage complet, des saegens et Gabarits avec soulèvement hydraulique avec fissure puissance d’entraînement de 30 kW avec unité hydraulique avec armoire électrique complète

Rampe de bois rond 4-4 avec déposant Möhringer Dimensions: Tirage de bois rond de 6,00 mètres de long, 6,00 mètres de large Déposant 6,00 mètres de long, 1,50 mètre de large l’installation est à 4 voies avec des moteurs électriques et de l’unité hydraulique

Spécifications Ruwac WS 2220 M: Puissance d’aspiration : 2 400 watts Puissance aérienne: 290 m3/h Tension: 230 volts Vide: 210 mbar Filtrer le filtre de poche : 1,2 ou 2,6 m2 Volume de conteneurs : 35 litres Filtre à poussière résiduel : 3,2 m2 Niveau de pression sonore : 67 dB(A) Connexion d’aspiration: 50mm

COMPLETE HIGHSPEED SAWMILL LINE (capacité 80 000 fm) : -Logortingline avec debar CAMBkingIO (6 mètres), 16 boîtes de tri ... de l' berger Wolf roundwood SORTING CRANE type Favorit 2000 Wagon Machine description ci-dessous:La largeur de l’avant: 3,80 mDrive: Hydrostatic,Speed infiniment 0-120 m / min2-circuit système de pompe avec 38 l / min30 - KW - moteur pour grue et hydraulique de conduite, urdant siège conducteurconstructed derrière la cabine De chargement hydraulique type grue Epsilon 25 155 S avec pincer et tête rotative sans fin Le convoyeur croisé de 5-5- échoué et se compose du convoyeur, de la longueur de 5,80 m, Width 5,Sing rising and slices - arbiter, longueur 2,70 m, Blocktrain 29,5 mlg, 0,75 m de large, avec Endschalterfahne, époseurs pour serrant la voiture avec 5 drapeaux L'HIGH PERFORMANCE SASH GANG SAW ESTERER EWD HD 30 BV710 mm ;; 300 U / min Avec r ...

A vendre séchoir rotatif en Bison, débit 5 t/h, avec poêle de chauffage 6mW avec auto-alimentation et auto-nettoyage en mouvement fllor. Avec tout l’équipement nécessaire, cyclon, cheminée et ventilateurs. Prix 110.000,00 EUR EXW. +38765812388 Neven

A vendre broyeur renouvelé fabriqué par HOMBACK avec 250kw. Utilisé pour déchiqueter le bois dans le bois de copeaux de till long.

Drum crusher with hydraulic pusherKnife drum width: 800 mmMouth 800 x 1200 mmMotor: 18,5 kWextraction connection diameter 200 mm

Semi-automatic

Max working width: 1300mmMax working thickness: 140mmMax. machining width: 1300mmMotorized feed rollers2 brushing units

Workpiece thickness: 8 - 50 mmEdge thickness: Coil edges 0.4 - 3 mmFeed speed 10 m/minEquipment:manual height adjustment.Joint milling unit, 2 motors Panel edge heatingGluing area Pressure zone 1 driven and 2 non-driven rollersEnd trims, 2 x 0,8 kW motors, straight and chamfer 15°Top and bottom trimmingProfile scraping unit for PVC edgingGlue scrapers

Panel thickness: 8 - 50 mmThickness of the edges: 0,4- 3 mmFeed speed 8 - 11 m / minPU pressure rollersEquipment:Squaring unit, 2 motors 2,2 kWPanel edge heatingEdge magazine for coil and stripsHot melt application with rollerAirtec AT4510 unitThe Airtec aggregate is positioned so you can use Airtec or the standard glue potMotorized side pressure unitEnd trims, 2 motors, pneumatic positioning straight and with chamfertrimming unit above / belowContour trimming unitProfile scraping unitGlue scraping unitPolishing unitDetergent spray systemcentral lubrication

Fixed side at the leftFeedspeed 18 - 25 m/minWorking width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mmPanel overhang 30mmPanel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations)Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mmCoil diameter 830 mmEquipment:Sprayers release agentSquaring device with 2 motors each 3 kWEdge heatingEdge magazine for 2 coils, guillotine for edges up to 3 mmGlueing part A20 with quickmelt applicationLateral pressure zone K, 1 driven and 6 after pressing rollersEnd trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kWContour trimming, 2 exchange unitsProfile scraping PN10Flat scrapers FA11Sprayers cleaning agentBuffingAutomation package straight/chamfer:-Automatic adjustment infeed fence-Automatic setting of pressure rollers-Pneumatic setting of end trims-Pneumatic setting of rough trims-Automatic setting of chamfer/ra ...

Single sided edge bander with hot melt, fixed side at the right, pre-milling unitEdge thickness: 0,4 to 12 mmWorkpiece thickness: 8 - 60 mmFeedspeed 8-20 m/min (limited to 10 m/min using the contour trimming)Workpiece transport by chain, top pressures with rubber rollersSound enclosure over all trimming motorsEquipment:Adjustable fencePre-milling with 2 shapers, each 2,2 kWCoil and strip magazine Hot melt unit, Quickmelt type Pressure zone with1 driven and 2 non-driven pneum. Loaded rollersEnd trims, 2 x 0,35 kW motors, straight and chamfer 15°Top/bottom trimming, motors 2 x 0,35 kWRadius trimmmingContour trimming unit, leading and following edge, 2 x 0,35 kWRadius scraping unitGlue scrapersBuffing unitControlls PC 20+

Workpiece thickness: 8 - 90 mm, electronically adjustableFeed rate: 18-32 m/min frequency controlledEdge thickness: 0.3 - 3 mm for roll edges, strips up to 20 mmEquipment:Inlet guide automatically adjustable via the control, extension 500 mmJoint milling unit: 2 x 3.0 KWworkpiece preheatingGluing unit A34edging magazine for rollPressure zone with 1 driven, 6 non-driven rollers, automatic adjustment from the controlCutting unit WK14, straight, 2 motors 0.8 kWPre-milling unit: 2 x 1.5 KW, pneumatic adjustmentForm milling unit FF 12 automatic, 2 motors 0.4 kWradius/phase milling unit FF12 automatic 4 motors 0.4 KWuniversal milling aggregate controlled UF11, 4 kWProfile scrapers PN20Glue scrapersNozzles for detergent and anti-stickPolishing unitControl: Power Control PC22

Fixed side at the leftFeedspeed 18 - 25 m/minWorking width min 60mm for panel thickness 22mm, 105mm for panel thickness 40mmPanel overhang 30mmPanel thickness 8 - 60 mm in stead of 12 - 40 mm (with limitations)Coil edge thickness: 0,3 - 3 mm, strips 0,4 - 20 mmCoil diameter 830 mmEquipment:Sprayers release agentSquaring device with 2 motors each 3 kWEdge heatingEdge magazine for 2 coils, guillotine for edges up to 3 mmGlueing part A20 with quickmelt applicationLateral pressure zone K, 1 driven and 6 after pressing rollersEnd trims HL84, 2 motors each 0,8kW Rough trimming, 2 motors 1,5kWContour trimming, 2 exchange unitsProfile scraping PN10Flat scrapers FA11Sprayers cleaning agentBuffingAutomation package straight/chamfer:-Automatic adjustment infeed fence-Automatic setting of pressure rollers-Pneumatic setting of end trims-Pneumatic setting of rough trims-Automatic setting of chamfer/ra ...

Fixed side at the leftPanel thickness min/max: 16/45 mmMin. panel width: 150 mmLateral panel support for panel width up to 900 mmMin/max. panel length: 700 / 3100 mmMax. laminate overhang: 110 mmMax. laminate thickness: 0,8 mmRadius min/max: 6 / 22 mm (depends the laminate)Feedspeed max. 18 m/minTop pressure by beltEquipment:Infeed fence, adjustable, defines the panel overhang2 x trimming unit 0,4 kW, HSK 25 toolholder1 x PVAc glue application5 x glue nozzle, adjustable1 x hot air blower3 x IR heating on top (55 cm length), 3 x bottom (90 cm length)Postforming zone 1,8 m. lengthVarious pre-installed profiling sets 1 x top trimmer 0,4 kW

Machining center in vertical design with automatic returnWorkpiece dimensions:Length: 200 to 3050 mmWidth: 50 to 1250 mmThickness: 8 to 80 mmweight max 60 kgPerformance- 2x vertical drilling unit separately controllable with variable speed. right left V10/32mm. 2.3 kW. Drill length 70 mm, D= max 35 mm- 2x horizontal drilling unit, 6 spindles in X direction, variable speed. right left can be controlled separately. Drill length 70 mm, D= max 20 mm- 2x horizontal drilling unit, 2 spindles in Y direction, variable speed. right left can be controlled separately. Drill length 70 mm, D= max 20 mm- Grooving saw unit X-Y can be swiveled 0°/90° saw diameter 125 mm, rpm 1500-7500 frequency controlled- Dowel insertion station for automatic insertion of dowels on the two transverse workpiece edges 1x left side / 1x right side glue pump, vibrating guide for dowels 8 x 35/40 mm- plausib ...

4-axis machining centerworking area: X Y Z : 3060 x 1080 x 155 mmMovement speed X 100 m/min, Y 100 m/min, Z 30 m/min14 vertical spindles4 horizontal spindles in X direction2 horizontal spindles in Y directionGrooving saw 0° - 90°toolchanger 7 positionstoolchanger 10 positionsRouter 7,5 kW, ISO 30 , 1000 - 24000 r/min, c-axislock milling aggregate available in option

Gantry-type, 3-axis CNC machining centreWorking area (type 2132): approx. 3300 x 2100 mmVacuum table with multiple switchable zonesInput: AES lifting table for automatic sheet loadingOutput: conveyor belt with label printer (labels are printed and applied manually)Main spindle: HSD ES929, HSK-F63 mount, 7.5 kW (9 kW), speed up to 24,000 rpm, 800 Hz, 380 VMain spindle overhauled in 2023Drilling unit with 16 spindles: 6 vertical spindles in X, 4 vertical spindles in Y, 2 double horizontal spindles in X, 1 double horizontal spindle in YSlotting sawTool changer with 12 positionsVacuum: Becker vacuum pumps, system approx. 500 m³/hControl: OSAI control system with AES ProcessController, operation via console with touchscreen and keyboardOperating hours: approx. 2,100 h (machine life), main spindle overhauled at approx. 1,360 h

Working area: X 5005 x Y 1520 mm x Z 200 mmMain spindle travel: X 5910 mm, Y 1815 mm, Z 655 mm.Travel speed: X 80 m/min, Y 80 m/min, Z 25 m/min8 workpiece consoles with automatically positioning vacuum cupsEquipment:Drilling unit with 19 spindles, 7 vertical spindles in X, 6 vertical spindles in Y, 2 double horizontal spindles in X, 1 double horizontal spindle in Y Slotting sawMilling motor 12 kW, 1000–24,000 rpm, HSK-F 63 mounting, liquid-cooled, 5-axis controlledTool changer with 22 positions Vacuum pumps with 2 x 100 m³/h capacityPC controlMasterwork software Integrated waste conveyor

Bridge type Capacity for all units: 3300 x 1100 mm(alternating: 2 x 1025 x 1100 mm)Capacity for routing with tooldiameter 25 mm: 1550 mmWorkpiece thickness up to 300 mm (stroke Z-axis 600 mm)Speed in X and Y: 60 m/min, Z: 25 m/min, Vector: 85 m/min6 Support rails with LED positioning indicationVacuum: 100/140 m3/hControlls: Powercontrol PC85Waste/chip removal belt in machine baseMachine pneumatically prepared to take pneumatic clamps, 3 pcs clamps includedDrilling unit V9/H4, 13 spindles, motor 2,2 kWMain spindle DRIVE5C+, 5-axis, 10 kW, HSKF63 taper, speed 1000 to 24000 r/min, tooldiameter up to 180 mm for routing, 350 mm for cutting14-fold rotary toolchanger and pick-up place for a sawbladeWoodwop software

Working field: axis x: 3200 mm, axis y: 944 mm, axis z: 110mmMax programmable speed: axis x: 100 m/min, axis y: 75 m/min, axis z: 15 m/minDrill holder: diameter 10 mmSpindle speeds: 4000 rpmGrooving saw: diameter 120 mmDrill spindles: 24 horizontal spindles in X,10 vertical spindles in X lineWorking pressure air pressure: 6 barInstalled power: max 25 kWCapacity of vacuum tools: 40 m³/hCNC:screen: monochromatic 9”Floppy disk unit